General Pump

1/4” General Pump # 5.0 “Flusher” Type Sewer Nozzle 0 Front 3 Rear 5,000 PSI.

Features
• “Flusher” nozzles expel loose debris as hose travels through pipe
• 3 Rear (25°) facing nozzles advance hose through pipe
• High pressure nozzles are sized to match the flow and pressure specifications of the equipment
• Heat-treated Stainless Steel nozzles are wear and corrosion resistant
• Great for pipe, sewer and drain cleaning
• Compact design allows for maneuverability and cornering within pipes
• Works best on 2" to 4" Pipes

Specifications
• Nozzle Size: # 5.0
• Material: Stainless steel
• Maximum Pressure: 5,000 PSI
• Inlet: 1/4" NPT-F
• Outside Diameter (O.D.): .63”
• Weight: .05 lb

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

1/4” General Pump # 5.5 “Flusher” Type Sewer Nozzle 0 Front 3 Rear 5,000 PSI.

Features
• “Flusher” nozzles expel loose debris as hose travels through pipe
• 3 Rear (25°) facing nozzles advance hose through pipe
• High pressure nozzles are sized to match the flow and pressure specifications of the equipment
• Heat-treated Stainless Steel nozzles are wear and corrosion resistant
• Great for pipe, sewer and drain cleaning
• Compact design allows for maneuverability and cornering within pipes
• Works best on 2" to 4" Pipes

Specifications
• Nozzle Size: # 5.5
• Material: Stainless steel
• Maximum Pressure: 5,000 PSI
• Inlet: 1/4" NPT-F
• Outside Diameter (O.D.): .63”
• Weight: .05 lb

Please use Nozzle Chart to determine proper nozzle size

Nozzle Chart

General Pump ZGRS1000 Gear Reducer for 2.2 to 1, 1″ Shafted Engines, Up to 25 HP, J609A Flange, 47 and 66 Series pumps

Features:
• Eliminates need for belts and pulleys. Saves time and money
• Compact design for easier enclosure. Reduced size of mounting base
• Oversized bearing system is self-aligning. Reduces load on motor bearings and pump bearings
• Self-contained lubrication system Uses 90W gear lube for quiet, long life operation. Protects pump from failure due to gearbox oil loss. Protects gearbox from failure due to oil loss in pump
• Large, helical cut, hardened steel gears for quiet, long life operation
• Large capacity crankcase
• Reversible mounting for right or left hand drive gas engines. Includes reversible dipstick and oil level sight glass
• Model ZGRS1000 for a 1” keyed shaft

Specifications:
• Maximum BHP (Engine HP): 25
• Maximum Engine RPM: 3,600
• Reduction Ratio: 1:2.2
• Maximum Pump Speed: 1,450 RPM
• Oil Capacity (SP Industrial Pump Oil Series 220): 9.47 Oz
• Fits Engine Shaft Diameter: 1”
• Fits General Pump Models: 47 Series (1450 RPM Versions) 66 Series (1450 RPM Versions)
• Weight: 9.26 lb.

General Pump YGR1000P Gear Reducer for 2.2 to 1, 1″ Shafted Engines, Up to 24 HP, J609A Flange, 47, 47SS and 66 Series pumps

Features:
• Compact and lightweight
• Hardened steel helical gears for quiet operation
• Oil bath lubrication
• Dual bearing design for extended life
• J609a Flange mounts to most gasoline engines

Specifications:
• Horse Power: 18 - 24
• Drive Ratio: 2.176:1
• Maximum Pump Speed: 1,450 RPM
• Oil Capacity: 10 Oz
• Oil Grade: SAE90 Gear Lube
• Input (motor) Shaft Ø": 1”
• Output (pump) Shaft Ø": 24 mm
• Motor Flange (SAE): J609A
• Pump Flange: Fits 47, 47SS and 66 Series General Pump
• Weight: 5.8 lb.

General YG4032S / PA 30.0680.50 High Flow 32 GPM Straight, Rear Entry Spray Gun for Hydro Excavation.

Features:
• Shockproof plastic housing
• Unique design compensates for changes in pressure
• Internal construction of brass and Stainless Steel
• Ergonomic design
• Minimizes fatigue for the operator

Specifications:
• Max Volume: 32 GPM
• Rated Discharge Pressure: 4,050 PSI
• Max Discharge Pressure: 4,500 PSI
• Max Temp: 210° F.
• Inlet: 1/2" Female NPT
• Outlet: 1/2" Female NPT
• Materials: Stainless Steel, Brass, Plastic, Viton
• Weight: 2.8 lbs

General Pump #1.8mm Adjustable Chemical Injector, High Draw, Chemical Draw Up To 20% with 3/8" NPT-M. This 0 - 20% adjustable flow chemical injector is connected to the downstream side of the pressure pump and is activated when using a low pressure soap nozzle. Choose size based on flow rate of your pressure washer

Features
• Up tp a 20% injection draw rate
• Made in the USA
• A cost effective solution to your chemical application needs

Injector Specifications:
• Size: # 1.8 mm (2.0 to 3.0 GPM)
• Max Operating Pressure: 4,500 PSI
• Max Temperature: 195° F
• Inlet: 3/8” NPT-M
• Outlet: 3/8” NPT-M
• Chemical Port: 1/4” Hose Barb
• Materials: Brass, Stainless Steel, Viton
• Note: If between sizes, choose the smaller injector size
• Weight: 0.30 lbs

General Pump #1.8mm Adjustable Chemical Injector with Acid Kit, High Draw, Chemical Draw Up To 20% with 3/8" NPT-M. This 0 - 20% adjustable flow chemical injector is connected to the downstream side of the pressure pump and is activated when using a low pressure soap nozzle. Choose size based on flow rate of your pressure washer

Features
• Up tp a 20% injection draw rate
• Acid kit with ceramic check ball
• Made in the USA
• A cost effective solution to your chemical application needs

Injector Specifications:
• Size: # 1.8 mm (2.0 to 3.0 GPM)
• Max Operating Pressure: 4,500 PSI
• Max Temperature: 195° F
• Inlet: 3/8” NPT-M
• Outlet: 3/8” NPT-M
• Chemical Port: 1/4” Hose Barb
• Materials: Brass, Ceramic, Stainless Steel, Viton
• Note: If between sizes, choose the smaller injector size
• Weight: 0.30 lbs

General Pump #2.1mm Adjustable Chemical Injector, High Draw, Chemical Draw Up To 20% with 3/8" NPT-M. This 0 - 20% adjustable flow chemical injector is connected to the downstream side of the pressure pump and is activated when using a low pressure soap nozzle. Choose size based on flow rate of your pressure washer

Features
• Up tp a 20% injection draw rate
• Made in the USA
• A cost effective solution to your chemical application needs

Injector Specifications:
• Size: # 2.1 mm (3.0 to 5.0 GPM)
• Max Operating Pressure: 4,500 PSI
• Max Temperature: 195° F
• Inlet: 3/8” NPT-M
• Outlet: 3/8” NPT-M
• Chemical Port: 1/4” Hose Barb
• Materials: Brass, Stainless Steel, Viton
• Note: If between sizes, choose the smaller injector size
• Weight: 0.30 lbs

General Pump #2.1mm Adjustable Chemical Injector with Acid Kit, High Draw, Chemical Draw Up To 20% with 3/8" NPT-M. This 0 - 20% adjustable flow chemical injector is connected to the downstream side of the pressure pump and is activated when using a low pressure soap nozzle. Choose size based on flow rate of your pressure washer

Features
• Up tp a 20% injection draw rate
• Acid kit with ceramic check ball
• Made in the USA
• A cost effective solution to your chemical application needs

Injector Specifications:
• Size: # 2.1 mm (3.0 to 5.0 GPM)
• Max Operating Pressure: 4,500 PSI
• Max Temperature: 195° F
• Inlet: 3/8” NPT-M
• Outlet: 3/8” NPT-M
• Chemical Port: 1/4” Hose Barb
• Materials: Brass, Ceramic, Stainless Steel, Viton
• Note: If between sizes, choose the smaller injector size
• Weight: 0.30 lbs

General Pump #2.3mm Adjustable Chemical Injector, High Draw, Chemical Draw Up To 20% with 3/8" NPT-M. This 0 - 20% adjustable flow chemical injector is connected to the downstream side of the pressure pump and is activated when using a low pressure soap nozzle. Choose size based on flow rate of your pressure washer

Features
• Up tp a 20% injection draw rate
• Made in the USA
• A cost effective solution to your chemical application needs

Injector Specifications:
• Size: # 2.3 mm (5.0 to 8.0 GPM)
• Max Operating Pressure: 4,500 PSI
• Max Temperature: 195° F
• Inlet: 3/8” NPT-M
• Outlet: 3/8” NPT-M
• Chemical Port: 1/4” Hose Barb
• Materials: Brass, Stainless Steel, Viton
• Note: If between sizes, choose the smaller injector size
• Weight: 0.30 lbs

General Pump #2.3mm Adjustable Chemical Injector with Acid Kit, High Draw, Chemical Draw Up To 20% with 3/8" NPT-M. This 0 - 20% adjustable flow chemical injector is connected to the downstream side of the pressure pump and is activated when using a low pressure soap nozzle. Choose size based on flow rate of your pressure washer

Features
• Up tp a 20% injection draw rate
• Acid kit with ceramic check ball
• Made in the USA
• A cost effective solution to your chemical application needs

Injector Specifications:
• Size: # 2.3 mm (5.0 to 8.0 GPM)
• Max Operating Pressure: 4,500 PSI
• Max Temperature: 195° F
• Inlet: 3/8” NPT-M
• Outlet: 3/8” NPT-M
• Chemical Port: 1/4” Hose Barb
• Materials: Brass, Ceramic, Stainless Steel, Viton
• Note: If between sizes, choose the smaller injector size
• Weight: 0.30 lbs

General Pump #1.8mm Adjustable Chemical Injector 304 Stainless Steel, High Draw, Chemical Draw Up To 20% with 3/8" NPT-M. This 0 - 20% adjustable flow chemical injector is connected to the downstream side of the pressure pump and is activated when using a low pressure soap nozzle. Choose size based on flow rate of your pressure washer

Features
• Up tp a 20% injection draw rate
• 304 Stainless Steel
• Made in the USA
• A cost effective solution to your chemical application needs

Injector Specifications:
• Size: # 1.8 mm (2.0 to 3.0 GPM)
• Max Operating Pressure: 5,500 PSI
• Max Temperature: 190° F
• Inlet: 3/8” NPT-M
• Outlet: 3/8” NPT-M
• Chemical Port: 1/4” Hose Barb
• Materials: Stainless Steel, Viton
• Note: If between sizes, choose the smaller injector size
• Weight: 0.50 lbs

General Pump #2.1mm Adjustable Chemical Injector 304 Stainless Steel, High Draw, Chemical Draw Up To 20% with 3/8" NPT-M. This 0 - 20% adjustable flow chemical injector is connected to the downstream side of the pressure pump and is activated when using a low pressure soap nozzle. Choose size based on flow rate of your pressure washer

Features
• Up tp a 20% injection draw rate
• 304 Stainless Steel
• Made in the USA
• A cost effective solution to your chemical application needs

Injector Specifications:
• Size: # 2.1 mm (3.0 to 5.0 GPM)
• Max Operating Pressure: 5,500 PSI
• Max Temperature: 190° F
• Inlet: 3/8” NPT-M
• Outlet: 3/8” NPT-M
• Chemical Port: 1/4” Hose Barb
• Materials: Stainless Steel, Viton
• Note: If between sizes, choose the smaller injector size
• Weight: 0.50 lbs

General Pump #2.3mm Adjustable Chemical Injector 304 Stainless Steel, High Draw, Chemical Draw Up To 20% with 3/8" NPT-M. This 0 - 20% adjustable flow chemical injector is connected to the downstream side of the pressure pump and is activated when using a low pressure soap nozzle. Choose size based on flow rate of your pressure washer

Features
• Up tp a 20% injection draw rate
• 304 Stainless Steel
• Made in the USA
• A cost effective solution to your chemical application needs

Injector Specifications:
• Size: # 2.3 mm (5.0 to 8.0 GPM)
• Max Operating Pressure: 5,500 PSI
• Max Temperature: 190° F
• Inlet: 3/8” NPT-M
• Outlet: 3/8” NPT-M
• Chemical Port: 1/4” Hose Barb
• Materials: Stainless Steel, Viton
• Note: If between sizes, choose the smaller injector size
• Weight: 0.50 lbs

General Pump #1.8mm Fixed Chemical Injector, High Draw, Chemical Draw 20% with 3/8" NPT-M. This 20% fixed flow chemical injector is connected to the downstream side of the pressure pump and is activated when using a low pressure soap nozzle. Choose size based on flow rate of your pressure washer

Features
• 20% injection draw rate
• Made in the USA
• A cost effective solution to your chemical application needs

Injector Specifications:
• Size: # 1.8 mm (2.0 to 3.0 GPM)
• Max Operating Pressure: 4,500 PSI
• Max Temperature: 195° F
• Inlet: 3/8” NPT-M
• Outlet: 3/8” NPT-M
• Chemical Port: 1/4” Hose Barb
• Materials: Brass, Stainless Steel, Viton
• Note: If between sizes, choose the smaller injector size
• Weight: 0.30 lbs

General Pump #2.1mm Fixed Chemical Injector, High Draw, Chemical Draw 20% with 3/8" NPT-M. This 20% fixed flow chemical injector is connected to the downstream side of the pressure pump and is activated when using a low pressure soap nozzle. Choose size based on flow rate of your pressure washer

Features
• 20% injection draw rate
• Made in the USA
• A cost effective solution to your chemical application needs

Injector Specifications:
• Size: # 2.1 mm (3.0 to 5.0 GPM)
• Max Operating Pressure: 4,500 PSI
• Max Temperature: 195° F
• Inlet: 3/8” NPT-M
• Outlet: 3/8” NPT-M
• Chemical Port: 1/4” Hose Barb
• Materials: Brass, Stainless Steel, Viton
• Note: If between sizes, choose the smaller injector size
• Weight: 0.30 lbs

General Pump #2.3mm Fixed Chemical Injector, High Draw, Chemical Draw 20% with 3/8" NPT-M. This 20% fixed flow chemical injector is connected to the downstream side of the pressure pump and is activated when using a low pressure soap nozzle. Choose size based on flow rate of your pressure washer

Features
• 20% injection draw rate
• Made in the USA
• A cost effective solution to your chemical application needs

Injector Specifications:
• Size: # 2.3 mm (5.0 to 8.0 GPM)
• Max Operating Pressure: 4,500 PSI
• Max Temperature: 195° F
• Inlet: 3/8” NPT-M
• Outlet: 3/8” NPT-M
• Chemical Port: 1/4” Hose Barb
• Materials: Brass, Stainless Steel, Viton
• Note: If between sizes, choose the smaller injector size
• Weight: 0.30 lbs

GP TS12150 High Limit TS Series Thermal Switch 1/2" NPT 150º F with 68" Wire Lead

Features
• Simple installation
• 68” 18 AWG Cable
• Normally Closed
• Can be mounted in any position
• Factory calibrated
• Made in the USA
• Precision snap action internal switches

TS Series Snap Action Data Sheet

Specifications
• Maximum Pressure: 5,000 PSI
• Voltage: 5 AMPS at 120 VAC
• Cord Length: 68”
• Temperature: 150º F
• Inlet: 1/2” NPT
• Switch Dimensions: 2.5" x 1"
• Materials: Brass, Steel, Nylon, Epoxy
• Weight: 0.5 Lb