Solid Shaft Pump 3,500 - 4,999

General T9281 Triplex Plunger Pump. The preferred pump frame in the pressure cleaning industry

Features:
• Nickel plated forged brass manifold
• Large-capacity, die-cast, anodized aluminum oil-bath crankcase
• Over-sized connecting rods for maximum life
• Heavy-duty tapered roller bearing
• Solid ceramic plungers with continuously lubricated packings
• Unitized stainless steel inlet and discharge valves

WARNING: High Pressure Systems require a primary pressure regulating device (i.e. regulator, unloader) and a secondary pressure relief device (i.e. pop-off valve, relief valve). Failure to install such relief devices properly could result in personal injury or damage to pump or property. GP and PRI Industries do not assume any liability or responsibility for the operation of the user’s high pressure system.

Specifications:
• Triplex Plunger Pump
• Solid Shaft for Belt or Gear Drive
• Max. Volume: 4.0 GPM
• Max. Discharge Pressure: 4,000 PSI
• Max. Pump Speed: 1,750 RPM
• Shaft Diameter: 24mm Solid
• Max. Horsepower Requirements: 11.0 EBHP
• Maximum Inlet Pressure: 125 PSI
• Oil Capacity: 37.2oz.
• Max. Fluid Temp.: 165° F.
• Inlet Ports (2): 1/2-14 BSPP-F
• Discharge Ports (2): 3/8-19 BSPP-F
• Drive Side: Standard right
• Note: Item for sale is PUMP ONLY as shown in picture and does not include unloader which is required for proper operation
• Weight: 33.0 lb.

General TSF2021 66 Series High Flow Triplex Plunger Pump

Features:
• Oversized roller bearings
• Fully anodized crankcase
• Innovative new seal design extends seal life
• New plunger design improves thermal shock resistance
• New valve cap improves hydrostatic performance

Specifications Sheet

WARNING: High Pressure Systems require a primary pressure regulating device (i.e. regulator, unloader) and a secondary pressure relief device (i.e. pop-off valve, relief valve). Failure to install such relief devices properly could result in personal injury or damage to pump or property. GP and PRI Industries do not assume any liability or responsibility for the operation of the user’s high pressure system.

Specifications:
• Triplex Plunger Pump
• Solid Shaft for Belt or Gear Drive
• Max. Discharge Pressure: 3,600 PSI
• Max. Volume: 7.0 GPM @ 1,450 RPM
• Max. Volume: 8.5 GPM @ 1,750 RPM
• Shaft Diameter: 24mm Solid
• Max. Horsepower Requirements (EBHP): 17.3 @ 7.0 GPM/21.0 @ 8.5 GPM
• Maximum Inlet Pressure: 125 PSI
• Oil Capacity: 3.8oz.
• Max. Fluid Temp.: 165° F.
• Inlet Ports (2): 3/4"-14 BSP-F
• Discharge Ports (2): 3/8-19 BSP-F
• Drive Side: Standard right
• Dimensions: 14.94" x 9.78" x 6.99"
• Note: Item for sale is PUMP ONLY as shown in picture and does not include unloader which is required for proper operation
• Weight: 40.7 lb.

Comet Premium TWS 8035S Series Triplex Plunger Pump. This solid shaft 24mm pump is designed for Belt Drive, Gearbox or Flex Couplers

Features
• Crankcase: Die-Cast Aluminum Alloy for Protection Against Corrosion
• Piston Guides are Heat Treated Stainless Steel
• Highly Efficient Stainless Steel Check Valves
• Solid Ceramic Plungers
• Brass Manifold: Forged for Maximum Strength and Longer LifeI
• Solid Bronze Alloy Connection Rods
• Oil Cap: New Travel/Working Oil Cap
• High Quality Tapered Roller Bearings
• Large Oil Capacity Dissipates Heat and Improves Lubrication for Longer Life
• Long life seals

Specifications
• Max. Volume: 8.3 GPM
• Max. Discharge Pressure: 3,500 PSI
• Max. Pump Speed: 1,750 RPM
• Shaft Diameter: 24mm Solid
• Inlet Ports: 3/4" FPT
• Outlet Ports: 1/2" FPT
• Replaces Comet # 6514.0600.00
• Weight: 45.0 lb.

Comet Premium TW 8036S Series Triplex Plunger Pump. This solid shaft 24mm pump is designed for Belt Drive, Gearbox or Flex Couplers

Features
• Crankcase: Die-Cast Aluminum Alloy for Protection Against Corrosion
• Piston Guides are Heat Treated Stainless Steel
• Highly Efficient Stainless Steel Check Valves
• Solid Ceramic Plungers
• Brass Manifold: Forged for Maximum Strength and Longer LifeI
• Solid Bronze Alloy Connection Rods
• Oil Cap: New Travel/Working Oil Cap
• High Quality Tapered Roller Bearings
• Large Oil Capacity Dissipates Heat and Improves Lubrication for Longer Life
• Long life seals

Specifications
• Max. Volume: 8.6 GPM
• Max. Discharge Pressure: 3,600 PSI
• Max. Pump Speed: 1,450 RPM
• Shaft Diameter: 24mm Solid
• Inlet Ports: 3/4" FPT
• Outlet Ports: 1/2" FPT
• Replaces Comet # 6513.0900.00
• Weight: 45.0 lb.

Comet Premium TW 7036S Series Triplex Plunger Pump. This solid shaft 24mm pump is designed for Belt Drive, Gearbox or Flex Couplers

Features
• Crankcase: Die-Cast Aluminum Alloy for Protection Against Corrosion
• Piston Guides are Heat Treated Stainless Steel
• Highly Efficient Stainless Steel Check Valves
• Solid Ceramic Plungers
• Brass Manifold: Forged for Maximum Strength and Longer LifeI
• Solid Bronze Alloy Connection Rods
• Oil Cap: New Travel/Working Oil Cap
• High Quality Tapered Roller Bearings
• Large Oil Capacity Dissipates Heat and Improves Lubrication for Longer Life
• Long life seals

Specifications
• Max. Volume: 7.0 GPM
• Max. Discharge Pressure: 3,600 PSI
• Max. Pump Speed: 1,450 RPM
• Shaft Diameter: 24mm Solid
• Inlet Ports: 3/4" FPT
• Outlet Ports: 1/2" FPT
• Replaces Comet # 6513.0700.00
• Weight: 45.0 lb.

Comet Premium TW 8040S Series Triplex Plunger Pump. This solid shaft 30mm pump is designed for Belt Drive, Gearbox or Flex Couplers

Features
• Crankcase: Die-Cast Aluminum Alloy for Protection Against Corrosion
• Piston Guides are Heat Treated Stainless Steel
• Highly Efficient Stainless Steel Check Valves
• Solid Ceramic Plungers
• Brass Manifold: Forged for Maximum Strength and Longer LifeI
• Solid Bronze Alloy Connection Rods
• Oil Cap: New Travel/Working Oil Cap
• High Quality Tapered Roller Bearings
• Large Oil Capacity Dissipates Heat and Improves Lubrication for Longer Life
• Long life seals

Specifications
• Max. Volume: 8.6 GPM
• Max. Discharge Pressure: 4,000 PSI
• Max. Pump Speed: 1,450 RPM
• Shaft Diameter: 30mm Solid
• Inlet Ports: 3/4" FPT
• Outlet Ports: 1/2" FPT
• Replaces Comet # 6513.1700.00
• Weight: 45.0 lb.

General PMRTSF2021 Pump Made Ready 66 Series High Flow Triplex Plunger Pump. Pump is ready to use right out of the box

Features:
• Oversized roller bearings
• Fully anodized crankcase
• Innovative new seal design extends seal life
• New plunger design improves thermal shock resistance
• New valve cap improves hydrostatic performance

Specifications Sheet

WARNING: High Pressure Systems require a primary pressure regulating device (i.e. regulator, unloader) and a secondary pressure relief device (i.e. pop-off valve, relief valve). Failure to install such relief devices properly could result in personal injury or damage to pump or property. GP and PRI Industries do not assume any liability or responsibility for the operation of the user’s high pressure system.

Specifications:
• Triplex Plunger Pump
• Solid Shaft for Belt or Gear Drive
• Max. Discharge Pressure: 3,600 PSI
• Max. Volume: 7.0 GPM @ 1,450 RPM
• Max. Volume: 8.5 GPM @ 1,750 RPM
• Shaft Diameter: 24mm Solid
• Max. Horsepower Requirements (EBHP): 17.3 @ 7.0 GPM/21.0 @ 8.5 GPM
• Maximum Inlet Pressure: 125 PSI
• Oil Capacity: 33.8oz.
• Max. Fluid Temp.: 165° F.
• Inlet Ports (2): 3/4"-14 BSP-F
• Discharge Ports (2): 3/8-19 BSP-F

COMPONENTS:
• General TSF2021 Triplex Plunger Pump
• ZH284K Unloader, 4060 PSI, 10 GPM
• High pressure safety relief valve
• Thermal relief valve
• 3/8” Hose Barb and Clamp Keeps Hose Secure and Sealed
• 3/4” Garden Hose Inlet Fitting with 1/4” Side Port
• 3/8” QC brass socket Installed and 3/8” QC Plug Included
• Mounting rails included
• Note: Pumps are not tested prior to shipping and unloader will need to be adjusted
• Weight: 46 lb

Comet Premium TW 8036S Series Triplex Plunger Hot Water Pump with Kevlar Seals. This solid shaft 24mm pump is designed for Belt Drive, Gearbox or Flex Couplers

Features
• Crankcase: Die-Cast Aluminum Alloy for Protection Against Corrosion
• Piston Guides are Heat Treated Stainless Steel
• Highly Efficient Stainless Steel Check Valves
• Solid Ceramic Plungers
• Brass Manifold: Forged for Maximum Strength and Longer LifeI
• Solid Bronze Alloy Connection Rods
• Oil Cap: New Travel/Working Oil Cap
• High Quality Tapered Roller Bearings
• Large Oil Capacity Dissipates Heat and Improves Lubrication for Longer Life
• Hot Water Pump with Kevlar Seals

Specifications
• Max. Volume: 8.6 GPM
• Max. Discharge Pressure: 3,600 PSI
• Max. Pump Speed: 1,450 RPM
• Shaft Diameter: 24mm Solid
• Inlet Ports: 3/4" FPT
• Outlet Ports: 1/2" FPT
• Replaces Comet # 6513.0902.00
• Weight: 45.0 lb.

Annovi Reverberi / AR North America RTX60 Triplex Plunger Pump. The RTX60 delivers up to 14.0 GPM and 4,350 PSI. Spinning at 1,450 RPM, this 30mm sold shafted pump features a nickel plated brass head. Inlet thread is 1” F and discharge thread is 1/2”F.

Features:
• High-strength, non-porous pressed nickel-plated brass head for guaranteed safety and durability
• One-piece extra thick ceramic pistons for exceptional strength
• Stainless steel ball-type intake and delivery valves with high fluido-dynamic efficiency
• Dual sealing system with anti-extrusion ring support and lubrication with low pressure recirculation chambers
• Pump casing in high-strength aluminum alloy with oversized mounts
• Camshaft in forged, treated steel
• Oversized two-piece connecting-rods in low-friction aluminum alloy
• “Premium” quality tapered roller bearings for long lifetime
• Splash lubrication

Specifications:
• Max. Volume: 14.0 GPM
• Max. Discharge Pressure: 4,350 PSI
• Max. Pump Speed: 1,450 RPM
• Shaft Diameter: 30mm Solid
• Max. Horsepower Requirements: 41.8 EBHP
• Max. Fluid Temp.: 140° F.
• Inlet Tread: 1" Female
• Outlet Thread: 1/2" Female
• Oil capacity: 76 oz
• Weight: 72.0 lb.

Annovi Reverberi / AR North America RTX30 Triplex Plunger Pump. The RTX30 delivers up to 7.9 GPM and 4,350 PSI. Spinning at 1,450 RPM, this 30mm sold shafted pump features a nickel plated brass head. Inlet thread is 1” F and discharge thread is 1/2”F.

Features:
• High-strength, non-porous pressed nickel-plated brass head for guaranteed safety and durability
• One-piece extra thick ceramic pistons for exceptional strength
• Stainless steel ball-type intake and delivery valves with high fluido-dynamic efficiency
• Dual sealing system with anti-extrusion ring support and lubrication with low pressure recirculation chambers
• Pump casing in high-strength aluminum alloy with oversized mounts
• Camshaft in forged, treated steel
• Oversized two-piece connecting-rods in low-friction aluminum alloy
• “Premium” quality tapered roller bearings for long lifetime
• Splash lubrication

Specifications:
• Max. Volume: 7.9 GPM
• Max. Discharge Pressure: 4,350 PSI
• Max. Pump Speed: 1,450 RPM
• Shaft Diameter: 30mm Solid
• Max. Horsepower Requirements: 23.6 EBHP
• Max. Fluid Temp.: 140° F.
• Inlet Tread: 1" Female
• Outlet Thread: 1/2" Female
• Oil capacity: 76 oz
• Weight: 72.0 lb.

Annovi Reverberi / AR North America RTJ70 Triplex Plunger Pump. The new RTJ Series of pumps from AR North America are designed for high-pressure industrial washing applications. They are constructed of cast iron bodies and feature a forged brass head with a threaded style sight glass in the rear cover made of metal. Internal components include special solid ceramic plungers for long life and durability. Oversized premium tapered roller bearings and the precision supports assure proper shaft alignment and maximum life. Valve cages of special designed Ultra-Form provide positive seating and extended life. Two-piece connecting rods are bronze material oversized for strength and load disbursement. These pumps are designed for belt drive systems, with a 35mm solid crankshaft.

Specifications
• Max. Volume: 18.5 GPM
• Max. Discharge Pressure: 4,000 PSI
• Max. Pump Speed: 1,000 RPM
• Shaft Diameter: 35mm Solid
• Maximum Horsepower Requirements: 50.8 EBHP
• Max. Fluid Temp.: 140º F.
• Inlet Port: 1-1/2" Female
• Discharge Port: 1" Female
• Drive Side: Standard right
• Weight: 198.0 lb.
• Ship via truck

General HF25A 4,050 PSI 19.6 GPM Triplex Plunger Pump. A “New Generation” Pump

Features:
• A “New Generation” Pump
• Triplex Plunger Pump, available in 4 flows
• Patent-pending, symmetrical power end design featuring top and bottom mounting holes allowing for easy left to right shaft conversion
• Low-high pressure packing design with integrated cooling system
• • High volumetric efficiency suction/delivery valves featuring new spherical design of sealing areas
• Splash lubrication
• SAE-C hydraulic drive bell housing and flexible couplers available
• Available with external gear box (direct drive only)
• Optional pulsing capability using F10744201 lifting valve (not included)

Specifications Sheet

Materials:
• High resistance light alloy die cast crankcase
• 420 Stainless steel manifold, nickel treated
• Taper roller bearings
• Special anti-friction, forged, light alloy connecting rods
• Forged alloy steel crankshaft, hardened, tempered and nitrited
• Cast iron piston guide, nickel treated
• Solid ceramic plungers
• Stainless steel valves

Specifications:
• Maximum Inlet Pressure:. 45 PSI
• Maximum Fluid Temperature:. *140° F
• Inlet Port Thread:. 1” NPT-F
• Discharge Port Thread:. 3/4” NPT-F
• Shaft Diameter:. 1.575”/40 mm
• Stroke:. 1.969”/50 mm
• Pump Dimensions: . 20” x 14.5” x 9.4”
• Crankcase Oil Capacity:. 128.5 oz. (3.8 liters, use GP Series 220 Oil
• Ship via truck
• Weight: 132 lbs./60 kg